42 U.S.C. § 6311 — Definitions

Page 6754 TITLE 42—THE PUBLIC HEALTH AND WELFARE § 6309 1 So in original. Probably should be designated ‘‘(4)’’. in carrying out this part during the period cov- ered by such report, and those actions which the Secretary was required to take under this part during such period but which were not taken, to- gether with the reasons therefor. Nothing in this section provides a defense or justification for a failure by the Secretary to comply with a non- discretionary duty as provided for in this part. (Pub. L. 94–163, title III, § 338, Dec. 22, 1975, 89 Stat. 932; Pub. L. 95–619, title IV, § 425(h), title VI, § 691(b)(2), Nov. 9, 1978, 92 Stat. 3266, 3288; Pub. L. 100–12, § 10, Mar. 17, 1987, 101 Stat. 124.) Editorial Notes AMENDMENTS 1987—Pub. L. 100–12 inserted at end ‘‘Nothing in this section provides a defense or justification for a failure by the Secretary to comply with a nondiscretionary duty as provided for in this part.’’ 1978—Pub. L. 95–619 inserted requirement that each report under this section should account for actions taken by the Secretary, as well as actions not taken, during the covered period in carrying out this part and substituted ‘‘Secretary’’ for ‘‘Administrator’’, meaning Administrator of the Federal Energy Administration. § 6309. Authorization of appropriations (a) Authorizations for Secretary There are authorized to be appropriated to the Secretary not more than the following amounts to carry out his responsibilities under this part— (1) $1,700,000 for fiscal year 1976; (2) $1,500,000 for fiscal year 1977; (3) $3,300,000 for fiscal year 1978; and (4) $10,000,000 for fiscal year 1979. Amounts authorized for such purposes under paragraph (3) shall be in addition to amounts otherwise authorized and appropriated for such purposes. (b) Authorizations for Commission There are authorized to be appropriated to the Commission not more than the following amounts to carry out its responsibilities under this part— (1) $650,000 for fiscal year 1976; (2) $700,000 for fiscal year 1977; (3) $700,000 for fiscal year 1978; and (3) 1 $2,000,000 for fiscal year 1979. (c) Other authorizations There are authorized to be appropriated to the Secretary to be allocated not more than the fol- lowing amounts— (1) $1,100,000 for fiscal year 1976; (2) $2,500,000 for fiscal year 1977; and (3) $1,800,000 for fiscal year 1978. Such amounts shall, and any amounts author- ized to be appropriated under subsection (a), may be allocated by the Secretary to the Na- tional Institute of Standards and Technology. (Pub. L. 94–163, title III, § 339, Dec. 22, 1975, 89 Stat. 932; Pub. L. 95–70, § 3, July 21, 1977, 91 Stat. 276; Pub. L. 95–619, title IV, § 426, title VI, § 691(b)(2), Nov. 9, 1978, 92 Stat. 3267, 3288; Pub. L. 100–12, § 11(b)(8), Mar. 17, 1987, 101 Stat. 126; Pub. L. 100–418, title V, § 5115(c), Aug. 23, 1988, 102 Stat. 1433.) Editorial Notes AMENDMENTS 1988—Subsec. (c). Pub. L. 100–418 substituted ‘‘Na- tional Institute of Standards and Technology’’ for ‘‘Na- tional Bureau of Standards’’ in closing provisions. 1987—Pub. L. 100–12 inserted headings for subsecs. (a) to (c). 1978—Subsec. (a). Pub. L. 95–619, §§ 426(a), 691(b)(2), substituted ‘‘Secretary’’ for ‘‘Administrator’’, meaning Administrator of the Federal Energy Administration, in text preceding par. (1), ‘‘$3,300,000’’ for ‘‘$1,500,000’’ in par. (3), added par. (4), and provided that amounts au- thorized under par. (3) would be in addition to amounts otherwise authorized and appropriated. Subsec. (b)(3). Pub. L. 95–619, § 426(b), added second par. (3) relating to fiscal year 1979. Subsec. (c). Pub. L. 95–619, § 691(b)(2), substituted ‘‘Secretary’’ for ‘‘Administrator’’. 1977—Subsec. (c)(2). Pub. L. 95–70, § 3(a), substituted ‘‘$2,500,000’’ for ‘‘$700,000’’. Subsec. (c)(3). Pub. L. 95–70, § 3(b), substituted ‘‘$1,800,000’’ for ‘‘$700,000’’. PART A–1—CERTAIN INDUSTRIAL EQUIPMENT Editorial Notes CODIFICATION This part was, in the original, designated part C and has been changed to part A–1 for purposes of codifica- tion. § 6311. Definitions For purposes of this part— (1) The term ‘‘covered equipment’’ means one of the following types of industrial equip- ment: (A) Electric motors and pumps. (B) Small commercial package air condi- tioning and heating equipment. (C) Large commercial package air condi- tioning and heating equipment. (D) Very large commercial package air conditioning and heating equipment. (E) Commercial refrigerators, freezers, and refrigerator-freezers. (F) Automatic commercial ice makers. (G) Walk-in coolers and walk-in freezers. (H) Commercial clothes washers. (I) Packaged terminal air-conditioners and packaged terminal heat pumps. (J) Warm air furnaces and packaged boil- ers. (K) Storage water heaters, instantaneous water heaters, and unfired hot water storage tanks. (L) Any other type of industrial equipment which the Secretary classifies as covered equipment under section 6312(b) of this title. (2)(A) The term ‘‘industrial equipment’’ means any article of equipment referred to in subparagraph (B) of a type— (i) which in operation consumes, or is de- signed to consume, energy; (ii) which, to any significant extent, is dis- tributed in commerce for industrial or com- mercial use; and (iii) which is not a ‘‘covered product’’ as defined in section 6291(a)(2) of this title, Page 6755 TITLE 42—THE PUBLIC HEALTH AND WELFARE § 6311 other than a component of a covered product with respect to which there is in effect a de- termination under section 6312(c) of this title; without regard to whether such article is in fact distributed in commerce for industrial or commercial use. (B) The types of equipment referred to in this subparagraph (in addition to electric mo- tors and pumps, commercial package air con- ditioning and heating equipment, commercial refrigerators, freezers, and refrigerator-freez- ers, automatic commercial ice makers, com- mercial clothes washers, packaged terminal air-conditioners, packaged terminal heat pumps, warm air furnaces, packaged boilers, storage water heaters, instantaneous water heaters, and unfired hot water storage tanks) are as follows: (i) compressors; (ii) fans; (iii) blowers; (iv) refrigeration equipment; (v) electric lights and lighting power sup- ply circuits; (vi) electrolytic equipment; (vii) electric arc equipment; (viii) steam boilers; (ix) ovens; (x) kilns; (xi) evaporators; (xii) dryers; and (xiii) other motors. (3) The term ‘‘energy efficiency’’ means the ratio of the useful output of services from an article of industrial equipment to the energy use by such article, determined in accordance with test procedures under section 6314 of this title. (4) The term ‘‘energy use’’ means the quan- tity of energy directly consumed by an article of industrial equipment at the point of use, de- termined in accordance with test procedures established under section 6314 of this title. (5) The term ‘‘manufacturer’’ means any per- son who manufactures industrial equipment. (6) The term ‘‘label’’ may include any print- ed matter determined appropriate by the Sec- retary. (7) The terms ‘‘energy’’, ‘‘manufacture’’, ‘‘import’’, ‘‘importation’’, ‘‘consumer prod- uct’’, ‘‘distribute in commerce’’, ‘‘distribution in commerce’’, and ‘‘commerce’’ have the same meaning as is given such terms in sec- tion 6291 of this title. (8)(A) The term ‘‘commercial package air conditioning and heating equipment’’ means air-cooled, water-cooled, evaporatively-cooled, or water source (not including ground water source) electrically operated, unitary central air conditioners and central air conditioning heat pumps for commercial application. (B) The term ‘‘small commercial package air conditioning and heating equipment’’ means commercial package air conditioning and heating equipment that is rated below 135,000 Btu per hour (cooling capacity). (C) The term ‘‘large commercial package air conditioning and heating equipment’’ means commercial package air conditioning and heating equipment that is rated— (i) at or above 135,000 Btu per hour; and (ii) below 240,000 Btu per hour (cooling ca- pacity). (D) The term ‘‘very large commercial pack- age air conditioning and heating equipment’’ means commercial package air conditioning and heating equipment that is rated— (i) at or above 240,000 Btu per hour; and (ii) below 760,000 Btu per hour (cooling ca- pacity). (9)(A) The term ‘‘commercial refrigerator, freezer, and refrigerator-freezer’’ means refrig- eration equipment that— (i) is not a consumer product (as defined in section 6291 of this title); (ii) is not designed and marketed exclu- sively for medical, scientific, or research purposes; (iii) operates at a chilled, frozen, combina- tion chilled and frozen, or variable tempera- ture; (iv) displays or stores merchandise and other perishable materials horizontally, semivertically, or vertically; (v) has transparent or solid doors, sliding or hinged doors, a combination of hinged, sliding, transparent, or solid doors, or no doors; (vi) is designed for pull-down temperature applications or holding temperature applica- tions; and (vii) is connected to a self-contained con- densing unit or to a remote condensing unit. (B) The term ‘‘holding temperature applica- tion’’ means a use of commercial refrigeration equipment other than a pull-down tempera- ture application, except a blast chiller or freezer. (C) The term ‘‘integrated average tempera- ture’’ means the average temperature of all test package measurements taken during the test. (D) The term ‘‘pull-down temperature appli- cation’’ means a commercial refrigerator with doors that, when fully loaded with 12 ounce beverage cans at 90 degrees F, can cool those beverages to an average stable temperature of 38 degrees F in 12 hours or less. (E) The term ‘‘remote condensing unit’’ means a factory-made assembly of refrig- erating components designed to compress and liquefy a specific refrigerant that is remotely located from the refrigerated equipment and consists of one or more refrigerant compres- sors, refrigerant condensers, condenser fans and motors, and factory supplied accessories. (F) The term ‘‘self-contained condensing unit’’ means a factory-made assembly of re- frigerating components designed to compress and liquefy a specific refrigerant that is an in- tegral part of the refrigerated equipment and consists of one or more refrigerant compres- sors, refrigerant condensers, condenser fans and motors, and factory supplied accessories. (10)(A) The term ‘‘packaged terminal air conditioner’’ means a wall sleeve and a sepa- rate unencased combination of heating and cooling assemblies specified by the builder and intended for mounting through the wall. It in- cludes a prime source of refrigeration, sepa- Page 6756 TITLE 42—THE PUBLIC HEALTH AND WELFARE § 6311 1 So in original. A closing parenthesis probably should follow ‘‘volts’’. rable outdoor louvers, forced ventilation, and heating availability by builder’s choice of hot water, steam, or electricity. (B) The term ‘‘packaged terminal heat pump’’ means a packaged terminal air condi- tioner that utilizes reverse cycle refrigeration as its prime heat source and should have sup- plementary heat source available to builders with the choice of hot water, steam, or elec- tric resistant heat. (11)(A) The term ‘‘warm air furnace’’ means a self-contained oil- or gas-fired furnace de- signed to supply heated air through ducts to spaces that require it and includes combina- tion warm air furnace/electric air conditioning units but does not include unit heaters and duct furnaces. (B) The term ‘‘packaged boiler’’ means a boiler that is shipped complete with heating equipment, mechanical draft equipment, and automatic controls; usually shipped in one or more sections. (12)(A) The term ‘‘storage water heater’’ means a water heater that heats and stores water within the appliance at a thermostatically controlled temperature for delivery on demand. Such term does not in- clude units with an input rating of 4000 Btu per hour or more per gallon of stored water. (B) The term ‘‘instantaneous water heater’’ means a water heater that has an input rating of at least 4000 Btu per hour per gallon of stored water. (C) The term ‘‘unfired hot water storage tank’’ means a tank used to store water that is heated externally. (13) ELECTRIC MOTOR.— (A) GENERAL PURPOSE ELECTRIC MOTOR (SUBTYPE I).—The term ‘‘general purpose electric motor (subtype I)’’ means any motor that meets the definition of ‘‘General Pur- pose’’ as established in the final rule issued by the Department of Energy entitled ‘‘En- ergy Efficiency Program for Certain Com- mercial and Industrial Equipment: Test Pro- cedures, Labeling, and Certification Require- ments for Electric Motors’’ (10 CFR 431), as in effect on December 19, 2007. (B) GENERAL PURPOSE ELECTRIC MOTOR (SUBTYPE II).—The term ‘‘general purpose electric motor (subtype II)’’ means motors incorporating the design elements of a gen- eral purpose electric motor (subtype I) that are configured as 1 of the following: (i) A U-Frame Motor. (ii) A Design C Motor. (iii) A close-coupled pump motor. (iv) A Footless motor. (v) A vertical solid shaft normal thrust motor (as tested in a horizontal configura- tion). (vi) An 8-pole motor (900 rpm). (vii) A poly-phase motor with voltage of not more than 600 volts (other than 230 or 460 volts.1 (C) The term ‘‘definite purpose motor’’ means any motor designed in standard ratings with standard operating characteristics or standard mechanical construction for use under service conditions other than usual or for use on a particular type of application and which cannot be used in most general purpose applications. (D) The term ‘‘special purpose motor’’ means any motor, other than a general purpose motor or definite purpose motor, which has special operating characteristics or special mechanical construction, or both, designed for a particular application. (E) The term ‘‘open motor’’ means a motor having ventilating openings which permit pas- sage of external cooling air over and around the windings of the machine. (F) The term ‘‘enclosed motor’’ means a motor so enclosed as to prevent the free ex- change of air between the inside and outside of the case but not sufficiently enclosed to be termed airtight. (G) The term ‘‘small electric motor’’ means a NEMA general purpose alternating current single-speed induction motor, built in a two- digit frame number series in accordance with NEMA Standards Publication MG1–1987. (H) The term ‘‘efficiency’’ when used with respect to an electric motor means the ratio of an electric motor’s useful power output to its total power input, expressed in percentage. (I) The term ‘‘nominal full load efficiency’’ means the average efficiency of a population of motors of duplicate design as determined in accordance with NEMA Standards Publication MG1–1987. (14) The term ‘‘ASHRAE’’ means the Amer- ican Society of Heating, Refrigerating, and Air Conditioning Engineers. (15) The term ‘‘IES’’ means the Illuminating Engineering Society of North America. (16) The term ‘‘NEMA’’ means the National Electrical Manufacturers Association. (17) The term ‘‘IEEE’’ means the Institute of Electrical and Electronics Engineers. (18) The term ‘‘energy conservation stand- ard’’ means— (A) a performance standard that prescribes a minimum level of energy efficiency or a maximum quantity of energy use for a prod- uct; or (B) a design requirement for a product. (19) The term ‘‘automatic commercial ice maker’’ means a factory-made assembly (not necessarily shipped in one package) that— (A) consists of a condensing unit and ice- making section operating as an integrated unit, with means for making and harvesting ice; and (B) may include means for storing ice, dis- pensing ice, or storing and dispensing ice. (20) WALK-IN COOLER; WALK-IN FREEZER.— (A) IN GENERAL.—The terms ‘‘walk-in cool- er’’ and ‘‘walk-in freezer’’ mean an enclosed storage space refrigerated to temperatures, respectively, above, and at or below 32 de- grees Fahrenheit that can be walked into, and has a total chilled storage area of less than 3,000 square feet. (B) EXCLUSION.—The terms ‘‘walk-in cool- er’’ and ‘‘walk-in freezer’’ do not include products designed and marketed exclusively for medical, scientific, or research purposes. Page 6757 TITLE 42—THE PUBLIC HEALTH AND WELFARE § 6311 2 So in original. Two pars. (22) have been enacted. (21) The term ‘‘commercial clothes washer’’ means a soft-mount front-loading or soft- mount top-loading clothes washer that— (A) has a clothes container compartment that— (i) for horizontal-axis clothes washers, is not more than 3.5 cubic feet; and (ii) for vertical-axis clothes washers, is not more than 4.0 cubic feet; and (B) is designed for use in— (i) applications in which the occupants of more than one household will be using the clothes washer, such as multi-family housing common areas and coin laundries; or (ii) other commercial applications. (22) 2 The term ‘‘harvest rate’’ means the amount of ice (at 32 degrees F) in pounds pro- duced per 24 hours. (22) 2 SINGLE PACKAGE VERTICAL AIR CONDI- TIONER.—The term ‘‘single package vertical air conditioner’’ means air-cooled commercial package air conditioning and heating equip- ment that— (A) is factory-assembled as a single pack- age that— (i) has major components that are ar- ranged vertically; (ii) is an encased combination of cooling and optional heating components; and (iii) is intended for exterior mounting on, adjacent interior to, or through an out- side wall; (B) is powered by a single- or 3-phase cur- rent; (C) may contain 1 or more separate indoor grilles, outdoor louvers, various ventilation options, indoor free air discharges, duct- work, well plenum, or sleeves; and (D) has heating components that may in- clude electrical resistance, steam, hot water, or gas, but may not include reverse cycle re- frigeration as a heating means. (23) SINGLE PACKAGE VERTICAL HEAT PUMP.— The term ‘‘single package vertical heat pump’’ means a single package vertical air condi- tioner that— (A) uses reverse cycle refrigeration as its primary heat source; and (B) may include secondary supplemental heating by means of electrical resistance, steam, hot water, or gas. (Pub. L. 94–163, title III, § 340, as added Pub. L. 95–619, title IV, § 441(a), Nov. 9, 1978, 92 Stat. 3267; amended Pub. L. 102–486, title I, § 122(a), (f)(1), Oct. 24, 1992, 106 Stat. 2806, 2817; Pub. L. 109–58, title I, § 136(a), Aug. 8, 2005, 119 Stat. 634; Pub. L. 110–140, title III, §§ 312(a), 313(a), 314(a), Dec. 19, 2007, 121 Stat. 1564, 1568, 1569; Pub. L. 112–210, § 10(c)(1), Dec. 18, 2012, 126 Stat. 1525; Pub. L. 115–115, § 2(b)(1), Jan. 12, 2018, 131 Stat. 2280.) Editorial Notes AMENDMENTS 2018—Par. (2)(B)(v). Pub. L. 115–115 added cl. (v) and struck out former cl. (v) which read as follows: ‘‘ elec- tric lights;’’. 2012—Par. (2)(B)(xiii). Pub. L. 112–210 added cl. (xiii). 2007—Par. (1)(G) to (L). Pub. L. 110–140, § 312(a)(1), added subpar. (G) and redesignated former subpars. (G) to (K) as (H) to (L), respectively. Par. (13). Pub. L. 110–140, § 313(a), inserted par. head- ing, added subpars. (A) and (B), redesignated former subpars. (B) to (H) as (C) to (I), respectively, and struck out former subpar. (A) which read as follows: ‘‘The term ‘electric motor’ means any motor which is a gen- eral purpose T-frame, single-speed, foot-mounting, polyphase squirrel-cage induction motor of the Na- tional Electrical Manufacturers Association, Design A and B, continuous rated, operating on 230/460 volts and constant 60 Hertz line power as defined in NEMA Standards Publication MG1–1987.’’ Pars. (20), (21). Pub. L. 110–140, § 312(a)(2), (3), added par. (20) and redesignated former par. (20) as (21). Former par. (21) redesignated (22) relating to harvest rate. Par. (22). Pub. L. 110–140, § 314(a), added par. (22) relat- ing to single package vertical air conditioner. Pub. L. 110–140, § 312(a)(2), redesignated par. (21) as (22) relating to harvest rate. Par. (23). Pub. L. 110–140, § 314(a), added par. (23). 2005—Par. (1)(D) to (K). Pub. L. 109–58, § 136(a)(1), added subpars. (D) to (G) and redesignated former sub- pars. (D) to (G) as (H) to (K), respectively. Par. (2)(B). Pub. L. 109–58, § 136(a)(2), substituted ‘‘commercial package air conditioning and heating equipment, commercial refrigerators, freezers, and re- frigerator-freezers, automatic commercial ice makers, commercial clothes washers’’ for ‘‘small and large com- mercial package air conditioning and heating equip- ment’’ in introductory provisions. Pars. (8), (9). Pub. L. 109–58, § 136(a)(3), added pars. (8) and (9) and struck out former pars. (8) and (9) which read as follows: ‘‘(8) The term ‘small commercial package air condi- tioning and heating equipment’ means air-cooled, water-cooled, evaporatively-cooled, or water source (not including ground water source) electrically oper- ated, unitary central air conditioners and central air conditioning heat pumps for commercial application which are rated below 135,000 Btu per hour (cooling ca- pacity). ‘‘(9) The term ‘large commercial package air condi- tioning and heating equipment’ means air-cooled, water-cooled, evaporatively-cooled, or water source (not including ground water source) electrically oper- ated, unitary central air conditioners and central air conditioning heat pumps for commercial application which are rated at or above 135,000 Btu per hour and below 240,000 Btu per hour (cooling capacity).’’ Pars. (19) to (21). Pub. L. 109–58, § 136(a)(4), added pars. (19) to (21). 1992—Par. (1)(B) to (G). Pub. L. 102–486, § 122(a)(1), added subpars. (B) to (F) and redesignated former sub- par. (B) as (G). Par. (2)(B). Pub. L. 102–486, § 122(a)(2), in introductory provisions, substituted ‘‘pumps, small and large com- mercial package air conditioning and heating equip- ment, packaged terminal air-conditioners, packaged terminal heat pumps, warm air furnaces, packaged boilers, storage water heaters, instantaneous water heaters, and unfired hot water storage tanks)’’ for ‘‘pumps)’’, redesignated cls. (vi) to (x) and (xii) to (xiv) as cls. (v) to (ix) and (x) to (xii), respectively, and struck out former cls. (v) and (xi) which read ‘‘air con- ditioning equipment;’’ and ‘‘furnaces;’’, respectively. Par. (3). Pub. L. 102–486, § 122(f)(1), substituted ‘‘(3) The’’ for ‘‘(3) the’’. Pars. (8) to (18). Pub. L. 102–486, § 122(a)(3), added pars. (8) to (18). Statutory Notes and Related Subsidiaries EFFECTIVE DATE OF 2007 AMENDMENT Amendment by Pub. L. 110–140 effective on the date that is 1 day after Dec. 19, 2007, see section 1601 of Pub. Page 6758 TITLE 42—THE PUBLIC HEALTH AND WELFARE § 6312 L. 110–140, set out as an Effective Date note under sec- tion 1824 of Title 2, The Congress. EXTENDED PRODUCT SYSTEM REBATE PROGRAM Pub. L. 116–260, div. Z, title I, § 1005, Dec. 27, 2020, 134 Stat. 2430, provided that: ‘‘(a) DEFINITIONS.—In this section: ‘‘(1) ELECTRIC MOTOR.—The term ‘electric motor’ has the meaning given the term in section 431.12 of title 10, Code of Federal Regulations (as in effect on the date of enactment of this Act [Dec. 27, 2020]). ‘‘(2) ELECTRONIC CONTROL.—The term ‘electronic control’ means— ‘‘(A) a power converter; or ‘‘(B) a combination of a power circuit and control circuit included on 1 chassis. ‘‘(3) EXTENDED PRODUCT SYSTEM.—The term ‘ex- tended product system’ means an electric motor and any required associated electronic control and driven load that— ‘‘(A) offers variable speed or multispeed oper- ation; ‘‘(B) offers partial load control that reduces input energy requirements (as measured in kilowatt- hours) as compared to identified base levels set by the Secretary of Energy (in this section referred to as the ‘Secretary’); and ‘‘(C)(i) has greater than 1 horsepower; and ‘‘(ii) uses an extended product system technology, as determined by the Secretary. ‘‘(4) QUALIFIED EXTENDED PRODUCT SYSTEM.— ‘‘(A) IN GENERAL.—The term ‘qualified extended product system’ means an extended product system that— ‘‘(i) includes an electric motor and an elec- tronic control; and ‘‘(ii) reduces the input energy (as measured in kilowatt-hours) required to operate the extended product system by not less than 5 percent, as compared to identified base levels set by the Sec- retary. ‘‘(B) INCLUSIONS.—The term ‘qualified extended product system’ includes commercial or industrial machinery or equipment that— ‘‘(i)(I) did not previously make use of the ex- tended product system prior to the redesign de- scribed in subclause (II); and ‘‘(II) incorporates an extended product system that has greater than 1 horsepower into rede- signed machinery or equipment; and ‘‘(ii) was previously used prior to, and was placed back into service during, calendar year 2021 or 2022. ‘‘(b) ESTABLISHMENT.—Not later than 180 days after the date of enactment of this Act, the Secretary shall establish a program to provide rebates for expenditures made by qualified entities for the purchase or installa- tion of a qualified extended product system. ‘‘(c) QUALIFIED ENTITIES.— ‘‘(1) ELIGIBILITY REQUIREMENTS.—A qualified entity under this section shall be— ‘‘(A) in the case of a qualified extended product system described in subsection (a)(4)(A), the pur- chaser of the qualified extended product that is in- stalled; and ‘‘(B) in the case of a qualified extended product system described in subsection (a)(4)(B), the manu- facturer of the commercial or industrial machinery or equipment that incorporated the extended prod- uct system into that machinery or equipment. ‘‘(2) APPLICATION.—To be eligible to receive a rebate under this section, a qualified entity shall submit to the Secretary— ‘‘(A) an application in such form, at such time, and containing such information as the Secretary may require; and ‘‘(B) a certification that includes demonstrated evidence— ‘‘(i) that the entity is a qualified entity; and ‘‘(ii)(I) in the case of a qualified entity de- scribed in paragraph (1)(A)— ‘‘(aa) that the qualified entity installed the qualified extended product system during the 2 fiscal years following the date of enactment of this Act; ‘‘(bb) that the qualified extended product sys- tem meets the requirements of subsection (a)(4)(A); and ‘‘(cc) showing the serial number, manufac- turer, and model number from the nameplate of the installed motor of the qualified entity on which the qualified extended product system was installed; or ‘‘(II) in the case of a qualified entity described in paragraph (1)(B), demonstrated evidence— ‘‘(aa) that the qualified extended product sys- tem meets the requirements of subsection (a)(4)(B); and ‘‘(bb) showing the serial number, manufac- turer, and model number from the nameplate of the installed motor of the qualified entity with which the extended product system is inte- grated. ‘‘(d) AUTHORIZED AMOUNT OF REBATE.— ‘‘(1) IN GENERAL.—The Secretary may provide to a qualified entity a rebate in an amount equal to the product obtained by multiplying— ‘‘(A) an amount equal to the sum of the name- plate rated horsepower of— ‘‘(i) the electric motor to which the qualified extended product system is attached; and ‘‘(ii) the electronic control; and ‘‘(B) $25. ‘‘(2) MAXIMUM AGGREGATE AMOUNT.—A qualified en- tity shall not be entitled to aggregate rebates under this section in excess of $25,000 per calendar year. ‘‘(e) AUTHORIZATION OF APPROPRIATIONS.—There is au- thorized to be appropriated to carry out this section $5,000,000 for each of fiscal years 2022 and 2023.’’ § 6312. Purposes and coverage (a) Congressional statement of purpose It is the purpose of this part to improve the ef- ficiency of electric motors and pumps and cer- tain other industrial equipment in order to con- serve the energy resources of the Nation. (b) Inclusion of industrial equipment as covered equipment The Secretary may, by rule, include a type of industrial equipment as covered equipment if he determines that to do so is necessary to carry out the purposes of this part. (c) Inclusion of component parts of consumer products as industrial equipment The Secretary may, by rule, include as indus- trial equipment articles which are component parts of consumer products, if he determines that— (1) such articles are, to a significant extent, distributed in commerce other than as compo- nent parts for consumer products; and (2) such articles meet the requirements of section 6311(2)(A) of this title (other than clauses (ii) and (iii)). (Pub. L. 94–163, title III, § 341, as added Pub. L. 95–619, title IV, § 441(a), Nov. 9, 1978, 92 Stat. 3268.)